When you Add to Cart and want to

Internet Explorer Users - When you Add an item to Cart and want to continue shopping
Go ahead and close the second window and continue shopping with the original window.

ALL Parts are NEW unless marked Otherwise

5250 Transmission High Speed Gear without Bushing USED $17.50

5251 Transmission High Speed Gear Bushing used on 5250 Gear above $24.00

5252 Transmission Low Speed Gear without Bushing USED $20.00

click image for close up view

5253 Transmission Low Speed Gear Bushing used on 5252 gear above $24.00

5254 Transmission Low Speed Gear Thrust Washer
NEW $6.00

USED $3.00

5255 Transmission Low Speed Gear Snap Ring $2.95

5256 Transmission Shift Sleeve
NEW $24.95

USED Choice 1 $10.00

USED Choice 2 $10.00

5257 Transmission Shift Fork

USED $15.00

5258 Transmission Shift Fork Shaft
NEW $7.00

USED $3.50

5259 Transmission Shift Fork Shaft Oil Seal $4.95

5260 Transmission Shift Arm
NEW $13.00

USED $6.50

5261 Tine Spring Holder Thrust Washer 0.877 ID / 1.316 OD $1.95

5261A Tine Spring Holder Thrust Washer 0.894 ID / 1.375 OD $1.95

5261B Tine Spring Holder Thrust Washer 1.02 ID / 1.500 OD $1.95

5262 Transmission Shift Lever
NEW $25.00

USED $10.00
click image for close up

5263 Clutch Shift Dog Lever Snap Ring $1.50

5263A Transmission Shift Lever Snap Ring $2.00

5264 Transmission Shift Lever Bushing $2.00

5265 (5615) Transmission Shift Control Rod for Models 6 & 6RS $7.00

5266 Transmission Axle USED without Bushing $19.00

USED 5266 Transmission Axle with 5251 Bushing $25.00
click image for close up

5267 Transmission High & Low Speed Gear Outer Bushing $22.00
Pressed into 5231 Transmission Case

5268 Wheel Inner Hub (OUT OF STOCK)

Transmission Axle Oil Seals

Select from these types of Transmission Axle Wheel Hub Housings

Direct Drive Wheel Hubs 5460 (No Clutch Hubs)

Frazer first used 5269 (National 50095) Transmission Oil Seal
which is shown in the Shop Manual, but not shown in the Parts Book

Also used is a 5461 Wheel Hub Oil Seal O-Ring
Not shown in the Shop Manual or Parts Book

Later Frazer switched to using 5767 which mounted inside the
Transmission Well instead of the Axle Housing.
These are no longer available from any company,
So I had them Custom Made and are available under my 5700-5799 button

5269 Transmission Wheel Hub Oil Seal - $19.00

5461 Wheel Hub O-Ring $2.00

5269 Used Transmission Oil Seal - Excellent Condition $10.00

Wheel Hub Housings with a Clutch Hubs 5585 & 5589
These used oil seal 5767 and later switched to 5585 which mounts in the Center
You can use both 5585 and 5767

5585 Oil Seal shown inserted 5571 Dust Seal replaces 5584

Free Wheeling Hubs 5934
These use oil seal 5269 $26.00

5270 Clutch Hub Lock Pin for B1-7's units with Free Wheeling $4.95

Fit's into the assembly below

5271 Free Wheeling Lock Pin Spring Short $2.00

5272 Free Wheeling Lock Pin Spring Long $2.00

5273 Tiller Drive (NOT AVAILABLE)

5274 Tiller Drive Housing USED $20.00

5275 Tiller Drive Housing Gasket $2.50

5276 Tiller Drive Housing Cover New $9.95 - Used $9.95

5277 Tiller Drive Housing Gasket $2.50

5278 Tiller Bevel Drive Gear New $20.00 Used $10.00

5279 Tiller Bevel Drive Key $0.95

5280 Tiller Drive Gear Shim 005 $0.95

5281 Tiller Drive Gear Pinion New $30.00 Used $15.00

5282 (Same as 5499) Tiller Drive Gear Pinion Front Needle Bearing
New $6.00

Used Bearings appears ok and roll smooth $3.00 (Only have 1)

5283 Tiller Drive Gear Pinion Rear Ball Bearing New $8.00 Used $4.00

5284 NEW Tiller Drive Shaft New $40.00 Used $20.00

5285 Tiller Drive Shaft Bearing Cone $25.00

5286 Tiller Drive Shaft Bearing Cup $20.00

5287 Tiller Drive Shaft Snap Ring Gear End 2.22 OD / 1.98 ID $1.95

5287A Tiller Drive Shaft Snap Ring Gear End 2.20 OD / 1.97 ID $1.95

5287B Tiller Drive Shaft Snap Ring Gear End 2.16 OD / 1.93 ID $1.95

5288 Tiller Drive Shaft Snap Ring Beveled $2.95

5289 Tiller Drive Shaft Oil Seal Rubber $24.00

To install use a thin piece of high durometer flexible plastic shim-style stock,
cut it to the same id as the rubber seal so it expands just a hair like a sleeve,
then seal slides right into place by tapping it in and the slip the shim out."